NAME

       ipmiutil_picmg - send specific PICMG extended IPMI commands

SYNOPSIS

       ipmiutil picmg [-mixNUPREFJTVY] parameters

DESCRIPTION

       This ipmiutil picmg subcommand sends specific PICMG/ATCA extended IPMI commands to the firmware.

       This  utility  can  use  either  the /dev/ipmi0 driver from OpenIPMI, the /dev/imb driver from Intel, the
       /dev/ipmikcs driver from valinux, direct user-space IOs, or the IPMI LAN interface if -N.

OPTIONS

       Command line options are described below.

       -i 00  This option specifies a specific FRU ID to show.  The input value should be in hex (0b, 1a, etc.),
              as shown from the sensor SDR output.  The default FRU ID is zero (0).

       -m 002000
              Show FRU for a specific MC (e.g. bus 00, sa 20, lun 00).  This could be used  for  PICMG  or  ATCA
              blade  systems.   The  trailing  character,  if  present, indicates SMI addressing if 's', or IPMB
              addressing if 'i' or not present.

       -x     Causes extra debug messages to be displayed.

       -N nodename
              Nodename or IP address of the remote  target  system.   If  a  nodename  is  specified,  IPMI  LAN
              interface is used.  Otherwise the local system management interface is used.

       -U rmt_user
              Remote username for the nodename given.  The default is a null username.

       -P/-R rmt_pswd
              Remote password for the nodename given.  The default is a null password.

       -E     Use the remote password from Environment variable IPMI_PASSWORD.

       -F drv_t
              Force  the driver type to one of the followng: imb, va, open, gnu, landesk, lan, lan2, lan2i, kcs,
              smb.  Note that lan2i means lan2 with intelplus.  The default is to detect  any  available  driver
              type and use it.

       -J     Use   the  specified  LanPlus  cipher  suite  (0  thru  17):  0=none/none/none,  1=sha1/none/none,
              2=sha1/sha1/none, 3=sha1/sha1/cbc128, 4=sha1/sha1/xrc4_128, 5=sha1/sha1/xrc4_40,  6=md5/none/none,
              ... 14=md5/md5/xrc4_40.  Default is 3.

       -T     Use a specified IPMI LAN Authentication Type: 0=None, 1=MD2, 2=MD5, 4=Straight Password, 5=OEM.

       -V     Use  a  specified  IPMI  LAN  privilege  level.  1=Callback level, 2=User level, 3=Operator level,
              4=Administrator level (default), 5=OEM level.

       -Y     Yes, do prompt the user for the IPMI LAN remote password.  Alternatives for the password are -E or
              -P.

PARAMETERS

       picmg parameters

              properties
                     Get PICMG properties may be used to obtain and print Extension major  version  information,
                     PICMG identifier, FRU Device ID and Max FRU Device ID.

              addrinfo

                     Get  address  information.   This  command  may return information on the Hardware address,
                     IPMB-0 Address, FRU ID, Site/Entity ID, and Site/Entity Type.

              frucontrol fru id options

                     Set various control options:

                     0x00      - Cold Reset

                     0x01      - Warm Reset

                     0x02      - Graceful Reboot

                     0x03      - Issue Diagnostic Interrupt

                     0x04      - Quiesce [AMC only]

                     0x05-0xFF - Cold Reset

              activate fru id

                     Activate the specified FRU.

              deactivate fru id

                     Deactivate the specified FRU.

              policy get fru id

                     Get FRU activation policy.

              policy set fru id lockmask lock

                     Set FRU activation policy.  lockmask is 1 or 0 to indicate action on  the  deactivation  or
                     activation locked bit respectively.  lock is 1 or 0 to set/clear locked bit.

              portstate set|getall|getgranted|getdenied parameters

                     Get or set various port states.  See usage for parameter details.

EXAMPLES

       ipmiutil picmg properties
       Gets PICMG properties from the default target address (slave address 0x20).

       ipmiutil picmg -N 192.168.1.1 -U root -P pswd addrinfo
       Gets PICMG Address Information from the specified IP address.

SEE ALSO

       ipmiutil(8)  ialarms(8)  iconfig(8)  idiscover(8)  ievents(8)  ifru(8)  igetevent(8)  ihealth(8)  ilan(8)
       ireset(8) isel(8) isensor(8) iserial(8) isol(8) iwdt(8)

WARNINGS

       See http://ipmiutil.sourceforge.net/ for the latest version of ipmiutil and any bug fix list.

COPYRIGHT

       Copyright (C) 2010  Kontron America, Inc.

       See the file COPYING in the distribution for more details regarding redistribution.

       This utility is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY.

AUTHOR

       Andy Cress <arcress at users.sourceforge.net>

                                            Version 1.0: 04 Jun 2010                                   IPICMG(8)