NAME

       rte_flow_attr

SYNOPSIS

       #include <rte_flow.h>

   Data Fields
       uint32_t group
       uint32_t priority
       uint32_t ingress:1
       uint32_t egress:1
       uint32_t transfer:1
       uint32_t reserved:29

Detailed Description

       Flow rule attributes.

       Priorities are set on a per rule based within groups.

       Lower values denote higher priority, the highest priority for a flow rule is 0, so that a flow that
       matches for than one rule, the rule with the lowest priority value will always be matched.

       Although optional, applications are encouraged to group similar rules as much as possible to fully take
       advantage of hardware capabilities (e.g. optimized matching) and work around limitations (e.g. a single
       pattern type possibly allowed in a given group). Applications should be aware that groups are not linked
       by default, and that they must be explicitly linked by the application using the JUMP action.

       Priority levels are arbitrary and up to the application, they do not need to be contiguous nor start from
       0, however the maximum number varies between devices and may be affected by existing flow rules.

       If a packet is matched by several rules of a given group for a given priority level, the outcome is
       undefined. It can take any path, may be duplicated or even cause unrecoverable errors.

       Note that support for more than a single group and priority level is not guaranteed.

       At vNIC / ethdev level, flow rules can apply to inbound and / or outbound traffic (ingress / egress),
       with respect to the vNIC / ethdev in question. At embedded switch level, flow rules apply to all traffic
       seen by it unless fitting meta items are used to set concrete traffic source(s).

       Several pattern items and actions are valid and can be used in both directions. Those valid for only one
       direction are described as such.

       At least one direction must be specified.

       Specifying both directions at once for a given rule is not recommended but may be valid in a few cases.

       Definition at line 89 of file rte_flow.h.

Field Documentation

   uint32_t group
       A group is a superset of multiple rules. The default group is 0 and is processed for all packets. Rules
       in other groups are processed only if the group is chained by a jump action from a previously matched
       rule. It means the group hierarchy is made by the flow rules, and the group 0 is the hierarchy root. Note
       there is no automatic dead loop protection.

       See also
           rte_flow_action_jump

       Definition at line 100 of file rte_flow.h.

   uint32_t priority
       Rule priority level within group.

       Definition at line 101 of file rte_flow.h.

   uint32_t ingress
       The rule in question applies to ingress traffic (non-'transfer').

       Definition at line 105 of file rte_flow.h.

   uint32_t egress
       The rule in question applies to egress traffic (non-'transfer').

       Definition at line 109 of file rte_flow.h.

   uint32_t transfer
       Instead of simply matching the properties of traffic as it would appear on a given DPDK port ID, enabling
       this attribute transfers a flow rule to the lowest possible level of any device endpoints found in the
       pattern.

       When supported, this effectively enables an application to re-route traffic not necessarily intended for
       it (e.g. coming from or addressed to different physical ports, VFs or applications) at the device level.

       The application should match traffic originating from precise locations. See items PORT_REPRESENTOR and
       REPRESENTED_PORT.

       Managing 'transfer' flows requires that the user communicate them through a suitable port.

       See also
           rte_flow_pick_transfer_proxy().

       Definition at line 127 of file rte_flow.h.

   uint32_t reserved
       Reserved, must be zero.

       Definition at line 128 of file rte_flow.h.

Author

       Generated automatically by Doxygen for DPDK from the source code.

DPDK                                             Version 24.11.2                                rte_flow_attr(3)