Provided by: vdr_2.6.9-3_amd64 
NAME
vdr - the Video Disk Recorder
SYNOPSIS
vdr [options]
DESCRIPTION
vdr implements a complete digital Set-Top Box and Video Recorder. It can work with signals received from
satellites (DVB-S) as well as cable (DVB-C) and terrestrial (DVB-T) signals.
At least one DVB card is required to run vdr. With it you can watch live TV while recording one or more
other broadcasts from the same transponder. It is also possible to start watching a recorded programme
before the live broadcast has ended (time shifting). In order to record from different transponders
simultaneously two or more DVB cards are necessary. By default vdr can support up to eight DVB cards.
The primary DVB card (the one your TV set is connected to) can either be a "full featured" card, which
means it contains an MPEG decoder and provides audio and video signal outputs, or you can use some third
party plugin that implements software decoding of the MPEG data and displays it via the system's graphics
adapter.
vdr uses an On Screen Display (OSD) to display its menus. It can be controlled by the PC keyboard, the
"Linux Infrared Remote Control" (LIRC), or any other means of remote control, implemented by a third
party plugin.
Remote access is possible via the "Simple Video Disk Recorder Protocol" (SVDRP), which can be accessed on
port 6419, for instance by telnet.
OPTIONS
-a cmd, --audio=cmd
Send Dolby Digital audio to stdin of command cmd.
--cachedir=dir
Save cache files in dir (default is to save them in the video directory).
--chartab=character_table
Set the character table to use for strings in the DVB data stream that don't begin with a
character table indicator, but don't use the standard default character table (for instance
ISO-8859-9).
-c dir, --config=dir
Read config files from directory dir (default is to read them from the video directory).
-d, --daemon
Run in daemon mode (implies --no-kbd).
-D num, --device=num
Use only the given DVB device (num = 0, 1, 2...). There may be several -D options (by default all
DVB devices will be used). If -D- is given, no DVB devices will be used at all, independent of
any other -D options.
--dirnames=path[,name[,enc]]
Set the maximum directory path length to path (default is the maximum value allowed on the
system). If name is also given, it defines the maximum directory name length (default is the
maximum value allowed on the system). The optional enc can be 0 or 1, and controls whether
special characters in directory names are encoded as hex values (default: 0). If path or name are
left empty (as in ",,1" to only set enc), the defaults apply. The length of the video directory
name and that of the actual recording directory is subtracted from path, to make sure the
directory path will never become too long.
--edit=rec
Edit the given recording. rec must be the full path name of an existing recording. The program
will return immediately after editing the recording.
-E file, --epgfile=file
Write the EPG data into the given file (default is epg.data in the cache directory). Use -E- to
disable this. If file is a directory, the file epg.data will be created in that directory.
--filesize=size
Limit video files to size bytes (default is 2000M). This option is only useful in conjunction
with --edit, and must precede that option to have an effect. size is an integer number and may be
followed by one of the letters K, M, G or T to abbreviate Kilo-, Mega-, Giga- or Terabyte,
respectively. The given value is silently limited to the program's internal minimum and maximum
values.
--genindex=rec
Generate the index file for the given recording. rec must be the full path name of an existing
recording. The recording must be in TS format. If the recording already has an index file, it
will be deleted before creating the new one. The program will return immediately after generating
the index. Note that using this option while another instance of VDR is currently replaying the
given recording, or if the recording has not been finished yet, may lead to unexpected results.
-g, --grab=dir
Write images from the SVDRP command GRAB into the given directory dir. dir must be the full path
name of an existing directory, without any "..", double '/' or symlinks. By default, or if -g- is
given, grabbing images to disk is disabled.
-h, --help
Print a help message and exit.
-i instance, --instance=instance
Use instance as the id of this VDR instance (default is 0). In an environment where several
instances of VDR use the same video directory, this parameter can be set to a positive integer
value that's unique for each instance, so that they won't interfere with each other in case they
record exactly the same broadcast. The number given here will be part of the directory name in
which the recordings will be stored.
-l level, --log=level
Set logging to level. 0 = no logging, 1 = errors only, 2 = errors and info, 3 = errors, info and
debug. The default logging level is 3. If logging should be done to LOG_LOCALn instead of
LOG_USER, add '.n' to LEVEL, as in 3.7 (n=0..7).
-L dir, --lib=dir
Search for plugins in directory dir (default is ./PLUGINS/lib). There can be several -L options
with different dir values. Each of them will apply to the -P options following it.
--lirc[=path]
Use a LIRC remote control device. If path is omitted, vdr uses /var/run/lirc/lircd.
--localedir=dir
Search for locale files in dir (default is ./locale).
-m, --mute
Mute audio of the primary DVB device at startup.
--no-kbd
Don't use the keyboard as an input device.
-p port, --port=port
Use port for SVDRP. A value of 0 turns off SVDRP. The default SVDRP port is 6419. You need to
edit the file svdrphosts.conf in order to enable access to the SVDRP port from hosts other than
the localhosts. Note that this option only changes the TCP port used for SVDRP commands. The UDP
port for discovering peer VDRs in the same network is always set to 6419 and can't be changed.
-P options, --plugin=options
Load a plugin, defined by the given options. The first word in options must be the name of an
existing vdr plugin, optionally followed by a blank separated list of command line options for
that plugin. If options contains any blanks, you need to enclose it in quotes, like for example
vdr -P "abc -a -b xyz"
which would load a plugin named abc, giving it the command line options -a -b xyz. If you want to
load all available plugins (without any particular options) you can use
vdr -P "*"
(note the quotes around the asterisk to prevent wildcard expansion).
-r cmd, --record=cmd
Call cmd before and after a recording. See the file INSTALL for more information.
--resdir=dir
Read resource files from dir (default is to read them from the config directory).
--showargs[=dir]
Read command line arguments from dir (default is /etc/vdr/conf.d), display them to the console and
exit.
-s cmd, --shutdown=cmd
Call cmd to shutdown the computer. See the file INSTALL for more information.
--split
Split edited files at the editing marks. This option is only useful in conjunction with --edit,
and must precede that option to have an effect.
-t tty, --terminal=tty
Set the controlling terminal.
-u user, --user=user
Run as user user in case vdr was started as user 'root'. Starting vdr as 'root' is necessary if
the system time shall be set from the transponder data, but for security reasons vdr can switch to
a lesser privileged user id during normal operation. user can be a user name or a numerical id.
--updindex=rec
Update the index file for the given recording. rec must be the full path name of an existing
recording. The recording must be in TS format. If the recording already has an index file, it
will be checked whether it is complete, and will be updated if it isn't. If there is no index file
yet, a new one will be generated. The program will return immediately after updating the index.
Note that using this option while another instance of VDR is currently replaying the given
recording, or if the recording has not been finished yet, may lead to unexpected results.
--userdump
Allow coredumps if -u is given (only for debugging).
--vfat For backwards compatibility (same as --dirnames= 250,40,1).
-v dir, --video=dir
Use dir as video directory. The default is /video.
-V, --version
Print version information and exit.
-w sec, --watchdog=sec
Activate the watchdog timer with a timeout of sec seconds. A value of 0 (default) disables the
watchdog.
If started without any options, vdr tries to read command line options from files named '*.conf' in the
directory /etc/vdr/conf.d. Files are read in alphabetical order. See vdr(5) for details.
SIGNALS
SIGINT, SIGTERM
Program exits with status 0.
SIGHUP Program exits with status 1. This can be used to force a reload, for example if an update has been
installed.
EXIT STATUS
0 Successful program execution.
1 An error has been detected which requires the DVB driver and vdr to be reloaded.
2 An non-recoverable error has been detected, vdr has given up.
FILES
channels.conf
Channel configuration.
timers.conf
Timer configuration.
setup.conf
User definable setup.
commands.conf
User definable commands (executed from the Commands menu).
svdrphosts.conf
SVDRP host configuration, defining which hosts or networks are given access to the SVDRP port.
marks Contains the editing marks defined for a recording.
info Contains a description of the recording.
resume Contains the index into the recording where the last replay session left off.
index Contains the file number, offset and type of each frame of the recording.
remote.conf
Contains the key assignments for the remote control.
keymacros.conf
Contains user defined remote control key macros.
00001.ts ... 65535.ts
The actual data files of a recording.
epg.data
Contains all current EPG data. Can be used for external processing and will also be read at
program startup to have the full EPG data available immediately.
donerecs.data
Contains the names of recordings that have been done by pattern timers with '@' as the first
character of the pattern. File names are appended to this file after a recording has finished, and
the entire file is read upon startup of VDR.
.update
If this file is present in the video directory, its last modification time will be used to trigger
an update of the list of recordings in the "Recordings" menu.
SEE ALSO
vdr(5),svdrpsend(1)
AUTHOR
Written by Klaus Schmidinger, with contributions from many others. See the file CONTRIBUTORS in the vdr
source distribution.
REPORTING BUGS
Report bugs to <vdr-bugs@tvdr.de>.
COPYRIGHT
Copyright © 2021 Klaus Schmidinger.
This is free software; see the source for copying conditions. There is NO warranty; not even for
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
2.6 27 Dec 2021 vdr(1)