NAME

       smp_conf_route_info - invoke CONFIGURE ROUTE INFORMATION SMP function

SYNOPSIS

       smp_conf_route_info   [--disable]  [--expected=EX]  [--help]  [--hex]  [--index=IN]  [--interface=PARAMS]
       [--phy=ID] [--raw] [--routed=R_SAS_ADDR] [--sa=SAS_ADDR] [--verbose] [--version] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Serial Management Protocol (SMP) CONFIGURE ROUTE  INFORMATION  function  request  to  an  SMP
       target. The SMP target is identified by the SMP_DEVICE and the --sa=SAS_ADDR. Depending on the interface,
       the SAS_ADDR may be deduced from the SMP_DEVICE.  The mpt interface uses SMP_DEVICE to identify a HBA (an
       SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present.

       There  are  two expander route table types: phy-based and expander-based.  The expander-based route table
       was introduced in SAS-2 and supersedes the  phy-based  route  tables.  The  CONFIGURE  ROUTE  INFORMATION
       function is associated with a phy-based route table. The REPORT ROUTE INFORMATION function is provided to
       report phy-based route table entries.

       Each  phy  in  a SAS expander that has an associated routing attribute of "table" has a router table. The
       number of rows (or entries) in each router table is given by the "expander route indexes"  field  in  the
       response of the REPORT GENERAL function.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -d, --disable
              set  the "disable expander route entry" flag in a row of the router table associated with --phy=ID
              of the given SMP target (e.g. an expander).  Within the router table the row that is  disabled  is
              identified by the expander route index given by --index=IN.

       -E, --expected=EX
              set  the  'expected  expander  change  count' field in the SMP request.  The value EX is from 0 to
              65535 inclusive with 0 being the default value. When EX is greater than zero  then  if  the  value
              doesn't  match  the  expander  change count of the SMP target (i.e. the expander) when the request
              arrives then the target ignores the request and sets a function result of "invalid expander change
              count" in the response.

       -h, --help
              output the usage message then exit.

       -H, --hex
              output the response (less the CRC field) in hexadecimal.

       -i, --index=IN
              expander route index. IN is a value between 0 and 65535. Default is 0.  More precisely the maximum
              index value is (expander_route_indexes - 1).

       -I, --interface=PARAMS
              interface specific parameters. In this case "interface" refers to the path through  the  operating
              system to the SMP initiator. See the smp_utils man page for more information.

       -p, --phy=ID
              phy identifier. ID is a value between 0 and 254. Default is 0.

       -r, --raw
              send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr.

       -R, --routed=R_SAS_ADDR
              specifies  the  SAS  address  to  be  placed  in  a  row (given by --index=IN) of the router table
              associated with --phy=ID. Default value is 0.  The R_SAS_ADDR is in decimal but most SAS addresses
              are given in hexadecimal. To give a number in hexadecimal either prefix it  with  '0x'  or  put  a
              trailing 'h' on it.

       -s, --sa=SAS_ADDR
              specifies the SAS address of the SMP target device. Typically this is an expander. This option may
              not be needed if the SMP_DEVICE has the target's SAS address within it. The SAS_ADDR is in decimal
              but  most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix it
              with '0x' or put a trailing 'h' on it.

       -v, --verbose
              increase the verbosity of the output. Can be used multiple times

       -V, --version
              print the version string and then exit.

CONFORMING TO

       The SMP CONFIGURE ROUTE INFORMATION function was introduced in SAS-1 .  The "Expander change count" field
       was added in SAS-2 .

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright © 2006-2011 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not even for  MERCHANTABILITY
       or FITNESS FOR A PARTICULAR PURPOSE.

SEE ALSO

       smp_utils, smp_rep_general, smp_rep_route_info(smp_utils)

smp_utils-0.96                                      May 2011                              SMP_CONF_ROUTE_INFO(8)