Provided by: freebsd-manpages_12.2-2_all 
NAME
sa — SCSI Sequential Access device driver
SYNOPSIS
device sa
DESCRIPTION
The sa driver provides support for all SCSI devices of the sequential access class that are attached to
the system through a supported SCSI Host Adapter. The sequential access class includes tape and other
linear access devices.
A SCSI Host adapter must also be separately configured into the system before a SCSI sequential access
device can be configured.
MOUNT SESSIONS
The sa driver is based around the concept of a “mount session”, which is defined as the period between
the time that a tape is mounted, and the time when it is unmounted. Any parameters set during a mount
session remain in effect for the remainder of the session or until replaced. The tape can be unmounted,
bringing the session to a close in several ways. These include:
1. Closing a `rewind device', referred to as sub-mode 00 below. An example is /dev/sa0.
2. Using the MTOFFL ioctl(2) command, reachable through the ‘offline’ command of mt(1).
It should be noted that tape devices are exclusive open devices, except in the case where a control mode
device is opened. In the latter case, exclusive access is only sought when needed (e.g., to set
parameters).
SUB-MODES
Bits 0 and 1 of the minor number are interpreted as ‘sub-modes’. The sub-modes differ in the action
taken when the device is closed:
00 A close will rewind the device; if the tape has been written, then a file mark will be written
before the rewind is requested. The device is unmounted.
01 A close will leave the tape mounted. If the tape was written to, a file mark will be written. No
other head positioning takes place. Any further reads or writes will occur directly after the last
read, or the written file mark.
10 A close will rewind the device. If the tape has been written, then a file mark will be written
before the rewind is requested. On completion of the rewind an unload command will be issued. The
device is unmounted.
BLOCKING MODES
SCSI tapes may run in either ‘variable’ or ‘fixed’ block-size modes. Most QIC-type devices run in fixed
block-size mode, where most nine-track tapes and many new cartridge formats allow variable block-size.
The difference between the two is as follows:
Variable block-size: Each write made to the device results in a single logical record written to the
tape. One can never read or write part of a record from tape (though you may request a larger block and
read a smaller record); nor can one read multiple blocks. Data from a single write is therefore read by
a single read. The block size used may be any value supported by the device, the SCSI adapter and the
system (usually between 1 byte and 64 Kbytes, sometimes more).
When reading a variable record/block from the tape, the head is logically considered to be immediately
after the last item read, and before the next item after that. If the next item is a file mark, but it
was never read, then the next process to read will immediately hit the file mark and receive an end-of-
file notification.
Fixed block-size: Data written by the user is passed to the tape as a succession of fixed size blocks.
It may be contiguous in memory, but it is considered to be a series of independent blocks. One may never
write an amount of data that is not an exact multiple of the blocksize. One may read and write the same
data as a different set of records. In other words, blocks that were written together may be read
separately, and vice-versa.
If one requests more blocks than remain in the file, the drive will encounter the file mark. As there is
some data to return (unless there were no records before the file mark), the read will succeed, returning
that data. The next read will return immediately with a value of 0. (As above, if the file mark is
never read, it remains for the next process to read if in no-rewind mode.)
BLOCK SIZES
By default, the driver will NOT accept reads or writes to a tape device that are larger than may be
written to or read from the mounted tape using a single write or read request. Because of this, the
application author may have confidence that his wishes are respected in terms of the block size written
to tape. For example, if the user tries to write a 256KB block to the tape, but the controller can
handle no more than 128KB, the write will fail. The previous FreeBSD behavior, prior to FreeBSD 10.0,
was to break up large reads or writes into smaller blocks when going to the tape. The problem with that
behavior, though, is that it hides the actual on-tape block size from the application writer, at least in
variable block mode.
If the user would like his large reads and writes broken up into separate pieces, he may set the
following loader tunables. Note that these tunables WILL GO AWAY in FreeBSD 11.0. They are provided for
transition purposes only.
kern.cam.sa.allow_io_split
This variable, when set to 1, will configure all sa devices to split large buffers into smaller
pieces when needed.
kern.cam.sa.%d.allow_io_split
This variable, when set to 1, will configure the given sa unit to split large buffers into multiple
pieces. This will override the global setting, if it exists.
There are several sysctl(8) variables available to view block handling parameters:
kern.cam.sa.%d.allow_io_split
This variable allows the user to see, but not modify, the current I/O split setting. The user is not
permitted to modify this setting so that there is no chance of behavior changing for the application
while a tape is mounted.
kern.cam.sa.%d.maxio
This variable shows the maximum I/O size in bytes that is allowed by the combination of kernel tuning
parameters (MAXPHYS, DFLTPHYS) and the capabilities of the controller that is attached to the tape
drive. Applications may look at this value for a guide on how large an I/O may be permitted, but
should keep in mind that the actual maximum may be restricted further by the tape drive via the SCSI
READ BLOCK LIMITS command.
kern.cam.sa.%d.cpi_maxio
This variable shows the maximum I/O size supported by the controller, in bytes, that is reported via
the CAM Path Inquiry CCB (XPT_PATH_INQ). If this is 0, that means that the controller has not
reported a maximum I/O size.
FILE MARK HANDLING
The handling of file marks on write is automatic. If the user has written to the tape, and has not done
a read since the last write, then a file mark will be written to the tape when the device is closed. If
a rewind is requested after a write, then the driver assumes that the last file on the tape has been
written, and ensures that there are two file marks written to the tape. The exception to this is that
there seems to be a standard (which we follow, but do not understand why) that certain types of tape do
not actually write two file marks to tape, but when read, report a `phantom' file mark when the last file
is read. These devices include the QIC family of devices. (It might be that this set of devices is the
same set as that of fixed block devices. This has not been determined yet, and they are treated as
separate behaviors by the driver at this time.)
PARAMETERS
The sa driver supports a number of parameters. The user can query parameters using “mt param -l” (which
uses the MTIOCPARAMGET ioctl) and the user can set parameters using “mt param -s” (which uses the
MTIOCPARAMSET ioctl). See mt(1) and mtio(4) for more details on the interface.
Supported parameters:
sili The default is 0. When set to 1, it sets the Suppress Incorrect Length Indicator (SILI) bit on
tape reads. Tape drives normally return sense data (which contains the residual) when the
application reads a block that is not the same length as the amount of data requested. The SILI
bit suppresses that notification in most cases. See the SSC-5 spec (available at t10.org),
specifically the section on the READ(6) command, for more information.
eot_warn
The default is 0. By default, the sa driver reports entering Programmable Early Warning, Early
Warning and End of Media conditions by returning a write with 0 bytes written, and errno set to 0.
If eot_warn is set to 1, the sa driver will set errno to ENOSPC when it enters any of the out of
space conditions.
protection.protection_supported
This is a read-only parameter, and is set to 1 if the tape drive supports protection information.
protection.prot_method
If protection is supported, set this to the desired protection method supported by the tape drive.
As of SSC-5r03 (available at t10.org), the protection method values are:
0 No protection.
1 Reed-Solomon CRC, 4 bytes in length.
2 CRC32C, 4 bytes in length.
protection.pi_length
Length of the protection information, see above for lengths.
protection.lbp_w
If set to 1, enable logical block protection on writes. The CRC must be appended to the end of
the block written to the tape driver. The tape drive will verify the CRC when it receives the
block.
protection.lbp_r
If set to 1, enable logical block protection on reads. The CRC will be appended to the end of the
block read from the tape driver. The application should verify the CRC when it receives the
block.
protection.rdbp
If set to 1, enable logical block protection on the RECOVER BUFFERED DATA command. The sa driver
does not currently use the RECOVER BUFFERED DATA command.
IOCTLS
The sa driver supports all of the ioctls of mtio(4).
FILES
/dev/[n][e]sa[0-9] general form:
/dev/sa0 Rewind on close
/dev/nsa0 No rewind on close
/dev/esa0 Eject on close (if capable)
/dev/sa0.ctl Control mode device (to examine state while another program is accessing the device,
e.g.).
DIAGNOSTICS
The sa driver supports injecting End Of Media (EOM) notification to aid application development and
testing. EOM is indicated to the application by returning the read or write with 0 bytes written. In
addition, when EOM is injected, the tape position status will be updated to temporarily show Beyond of
the Programmable Early Warning (BPEW) status. To see BPEW status, use the MTIOCEXTGET ioctl, which is
used by the “mt status” command. To inject an EOM notification, set the
kern.cam.sa.%d.inject_eom
sysctl variable to 1. One EOM notification will be sent, BPEW status will be set for one position query,
and then the driver state will be reset to normal.
SEE ALSO
mt(1), cam(4)
AUTHORS
The sa driver was written for the CAM SCSI subsystem by Justin T. Gibbs and Kenneth Merry. Many ideas
were gleaned from the st device driver written and ported from Mach 2.5 by Julian Elischer.
The owner of record for many years was Matthew Jacob. The current maintainer is Kenneth Merry
BUGS
This driver lacks many of the hacks required to deal with older devices. Many older SCSI-1 devices may
not work properly with this driver yet.
Additionally, certain tapes (QIC tapes mostly) that were written under FreeBSD 2.X are not automatically
read correctly with this driver: you may need to explicitly set variable block mode or set to the
blocksize that works best for your device in order to read tapes written under FreeBSD 2.X.
Partitions are only supported for status information and location. It would be nice to add support for
creating and editing tape partitions.
Debian May 5, 2017 SA(4)