Ubuntu Manpage: Conrec_family - is a set of two dimensional contour mapping routines. There are options for generating

Provided by: libncarg-dev_6.6.2.dfsg.1-10build2_amd64

NAME

       Conrec_family - is a set of two dimensional contour mapping routines.  There are options for generating
       standard contours, smoothing contour lines, labeling the contours, and removing crowded lines.

STATUS

       Conrec_family is obsolete.  It has been replaced by the contouring package, Conpack.  See the Conpack
       entry CPCNRC for a simple CONREC replacement.  For more complex examples refer to the conpack and
       conpack_params man pages as well as the NCAR Graphics Contouring and Mapping Tutorial.

       Conrec_family continues to be provided for compatibility of early NCAR Graphics codes.  If you are
       writing new code, we suggest that you use the more general and rigorous Conpack contouring package.  All
       Conrec_family options are available via Conpack parameters.

SYNOPSIS

       EZCNTR(Z,M,N) - draws a contour map based upon a set of default options.
       CONREC(Z,L,M,N,FLO,HI,FINC,NSET,NHI,NDOT) - draws a contour map using options specified as input
       arguments.

ACCESS

The Conrec family contains only two user callable entries, EZCNTR, and CONREC. However, these two
entries can be invoked in four different ways to create contour plots which vary considerably in
appearance. The four variations include quick, normal, smooth, and super contour lines. This
progression represents a tradeoff between speed of computation and the appearance of the contour plots.
These variations are specified through selected command line options of the ncargf77 command.

To use EZCNTR or CONREC, load the NCAR Graphics libraries ncarg, ncarg_gks, and ncarg_c, preferably in
that order. Other optional libraries to create the quick, smooth, and super contours will automatically
be linked by the ncargf77 command. To run a code called mycode.f which has one or more calls to entry
EZCNTR or CONREC, issue one of the commands:

NORMAL Command: "ncargf77 mycode.f"

The contours will be drawn as unsmoothed dashed or solid lines that can include characters
along the lines.

QUICK Command: "ncargf77 -quick mycode.f"

The contours will be drawn as unsmoothed dashed or solid lines without characters along the
lines. The QUICK drawing algorithm is faster and cruder than that used for NORMAL contour
lines. QUICK uses a cell-by-cell analysis rather than following each contour line to
completion in sequence as is done in the NORMAL algorithm.

SMOOTH Command: "ncargf77 -smooth mycode.f"

The contours will be drawn as smoothed dashed or solid lines using splines under tension.
There may be characters along the lines.

SUPER Command: "ncargf77 -super mycode.f"

The contours will be drawn as smoothed dashed or solid lines using splines under tension.
There may be characters along the lines. Crowded lines can be thinned.

MESSAGES

       When  error  conditions  are detected, the support routine SETER is called in such a way that it writes a
       message to the standard error file (as defined by I1MACH(4)) and then terminates execution. The  possible
       error messages are as follows:

       CONREC  - DIMENSION ERROR - M*N .GT. (2**IARTH)
       The  array to be contoured is dimensioned M by N.  This is larger than the address space on this computer
       (2**IARTH) where IARTH is the size of an address integer.  Check your dimension sizes.

       STLINE  - WARNING FROM ROUTINE STLINE IN CONREC--WORK ARRAY OVERFLOW
       This warning message is printed to standard output if the number of contour lines  for  a  contour  level
       would exceed the dimension size of work array IR in routine STLINE.

       Should this happen the following messages are also sent to the output plot file:

       **WARNING--PICTURE INCOMPLETE**
       WORK ARRAY OVERFLOW IN STLINE

       Processing stops before the actual array overflow occurs and control is returned to the calling program.

COPYRIGHT