Ubuntu Manpage: softflowd — Traffic flow monitoring

NAME

       softflowd — Traffic flow monitoring

SYNOPSIS

       softflowd [-6dDhbal] [-L hoplimit] [-T track_level] [-c ctl_sock] [-i  [if_ndx:]interface] [-m max_flows]
                 [-n  host:port]  [-p  pidfile]  [-r  pcap_file]  [-t timeout_name=seconds] [-v netflow_version]
                 [-P   transport_protocol]   [-A   time_format]   [-s   sampling_rate]    [-C    capture_length]
                 [-R receive_port] [bpf_expression]

DESCRIPTION

softflowd is a software implementation of a flow-based network traffic monitor. softflowd reads network
traffic and gathers information about active traffic flows. A "traffic flow" is communication between
two IP addresses or (if the overlying protocol is TCP or UDP) address/port tuples.

The intended use of softflowd is as a software implementation of Cisco's NetFlow(tm) traffic account
system. softflowd supports data export using versions 1, 5, 9 or 10 (a.k.a. IPFIX) of the NetFlow
protocol. softflowd can also run in statistics-only mode, where it just collects summary information.
However, too few statistics are collected to make this mode really useful for anything other than
debugging.

Network traffic may be obtained by listening on a promiscuous network interface or by reading stored
pcap(3) files, such as those written by tcpdump(8). Traffic may be filtered with an optional bpf(4)
program, specified on the command-line as bpf_expression. softflowd is IPv6 capable and will track IPv6
flows if the NetFlow export protocol supports it (currently only NetFlow v.9 possesses an IPv6 export
capability).

softflowd tries to track only active traffic flows. When the flow has been quiescent for a period of
time it is expired automatically. Flows may also be expired early if they approach their traffic counts
exceed 2 Gib or if the number of flows being tracked exceeds max_flows (default: 8192). In this last
case, flows are expired oldest-first.

Upon expiry, the flow information is accumulated into statistics which may be viewed using
softflowctl(8). If the -n option has been specified the flow information is formatted in a UDP datagram
which is compatible with versions 1, 5 or 9 of Cisco's NetFlow(tm) accounting export format. These
records are sent to the specified host and port. The host may represent a unicast host or a multicast
group.

The command-line options are as follows:

-n host:port
Specify the host and port that the accounting datagrams are to be sent to. The host may be
specified using a hostname or using a numeric IPv4 or IPv6 address. Numeric IPv6 addresses
should be enclosed in square brackets to avoid ambiguity between the address and the port. The
destination port may be a portname listed in services(5) or a numeric port. Comma can be used
for specifying multiple destinations.

-i [if_ndx:]interface
Specify a network interface on which to listen for traffic. Either the -i or the -r options must
be specified.

-r pcap_file
Specify that softflowd should read from a pcap(3) packet capture file (such as one created with
the -w option of tcpdump(8)) file rather than a network interface. softflowd processes the whole
capture file and only expires flows when max_flows is exceeded. In this mode, softflowd will not
fork and will automatically print summary statistics before exiting.

-p pidfile
Specify an alternate location to store the process ID when in daemon mode. Default is
/var/run/softflowd.pid

-c ctlsock
Specify an alternate location for the remote control socket in daemon mode. Default is
/var/run/softflowd.ctl

-m max_flows
Specify the maximum number of flows to concurrently track. If this limit is exceeded, the flows
which have least recently seen traffic are forcibly expired. In practice, the actual maximum may
briefly exceed this limit by a small amount as expiry processing happens less frequently than
traffic collection. The default is 8192 flows, which corresponds to slightly less than 800k of
working data.

-t timeout_name=time
Set the timeout names timeout_name to time. Refer to the “Timeouts” section for the valid
timeout names and their meanings. The time parameter may be specified using one of the formats
explained in the “Time Formats” section below.

-d Specify that softflowd should not fork and daemonise itself.

-6 Force softflowd to track IPv6 flows even if the NetFlow export protocol does not support
reporting them. This is useful for debugging and statistics gathering only.

-D Places softflowd in a debugging mode. This implies the -d and -6 flags and turns on additional
debugging output.

-b Bidirectional mode in IPFIX (-b work with -v 10)

-a Adjusting time for reading pcap file (-a work with -r)

-l Load balancing mode for multiple destinations which are specified with -n

-h Display command-line usage information.

-L hoplimit
Set the IPv4 TTL or the IPv6 hop limit to hoplimit. softflowd will use the default system TTL
when exporting flows to a unicast host. When exporting to a multicast group, the default TTL
will be 1 (i.e. link-local).

-T track_level
Specify which flow elements softflowd should be used to define a flow. track_level may be one
of: “ether” (track everything including source and destination addresses, source and destination
port, source and destination ethernet address, vlanid and protocol), “vlan” (track source and
destination addresses, source and destination port, vlanid and protocol), “full” (track source
and destination addresses, source and destination port and protocol in the flow, the default),
“proto” (track source and destination addresses and protocol), or “ip” (only track source and
destination addresses). Selecting either of the latter options will produce flows with less
information in them (e.g. TCP/UDP ports will not be recorded). This will cause flows to be
consolidated, reducing the quantity of output and CPU load that softflowd will place on the
system at the cost of some detail being lost.

-v netflow_version
Specify which version of the NetFlow(tm) protocol softflowd should use for export of the flow
data. Supported versions are 1, 5, 9, 10(IPFIX), and psamp. Default is version 5.

-P transport_protocol
Specify transport layer protocol for exporting packets. Supported transport layer protocols are
udp, tcp, and sctp.

-A time_format
Specify absolute time format form exporting records. Supported time formats are sec, milli,
micro, and nano.

-s sampling_rate
Specify periodical sampling rate (denominator).

-C capture_length
Specify length for packet capture (snaplen).

-R receive_port
Specify port number for PSAMP receive mode.

Any further command-line arguments will be concatenated together and applied as a bpf(4) packet filter.
This filter will cause softflowd to ignore the specified traffic.

Timeouts
softflowd will expire quiescent flows after user-configurable periods. The exact timeout used depends on
the nature of the flow. The various timeouts that may be set from the command-line (using the -t option)
and their meanings are:

general
This is the general timeout applied to all traffic unless overridden by one of the other
timeouts.

tcp This is the general TCP timeout, applied to open TCP connections.

tcp.rst
This timeout is applied to a TCP connection when a RST packet has been sent by one or both
endpoints.

tcp.fin
This timeout is applied to a TCP connection when a FIN packet has been sent by both endpoints.

udp This is the general UDP timeout, applied to all UDP connections.

maxlife
This is the maximum lifetime that a flow may exist for. All flows are forcibly expired when they
pass maxlife seconds. To disable this feature, specify a maxlife of 0.

expint Specify the interval between expiry checks. Increase this to group more flows into a NetFlow
packet. To disable this feature, specify a expint of 0.

Flows may also be expired if there are not enough flow entries to hold them or if their traffic exceeds 2
Gib in either direction. softflowctl(8) may be used to print information on the average lifetimes of
flows and the reasons for their expiry.

Time Formats
softflowd command-line arguments that specify time may be expressed using a sequence of the form:
time[qualifier], where time is a positive integer value and qualifier is one of the following:

Each member of the sequence is added together to calculate the total time value.

Time format examples:

600 600 seconds (10 minutes)
10m 10 minutes
1h30m 1 hour 30 minutes (90 minutes)

Run-time Control
A daemonised softflowd instance may be controlled using the softflowctl(8) command. This interface
allows one to shut down the daemon, force expiry of all tracked flows and extract debugging and summary
data. Also, receipt of a SIGTERM or SIGINT will cause softflowd to exit, after expiring all flows (and
thus sending flow export packets if -n was specified on the command-line). If you do not want to export
flows upon shutdown, clear them first with softflowctl(8) or use softflowctl(8) 's “exit” command.

EXAMPLES

softflowd -i fxp0
This command-line will cause softflowd to listen on interface fxp0 and to run in statistics
gathering mode only (i.e. no NetFlow data export).

softflowd -i fxp0 -n 10.1.0.2:4432
This command-line will cause softflowd to listen on interface fxp0 and to export NetFlow v.5
datagrams on flow expiry to a flow collector running on 10.1.0.2 port 4432.

softflowd -i fxp0 -n 10.1.0.2:4432,10.1.0.3:4432
This command-line will cause softflowd to listen on interface fxp0 and to export NetFlow v.5
datagrams on flow expiry to a flow collector running on 10.1.0.2 port 4432 and 10.1.0.3 port
4432.

softflowd -i fxp0 -l -n 10.1.0.2:4432,10.1.0.3:4432
This command-line will cause softflowd to listen on interface fxp0 and to export NetFlow v.5
datagrams on flow expiry to a flow collector running on 10.1.0.2 port 4432 and 10.1.0.3 port 4432
with load balncing mode. Odd netflow packets will be sent to 10.1.0.2 port 4432 and even netflow
packets will be sent to 10.1.0.3 port 4432.

softflowd -v 5 -i fxp0 -n 10.1.0.2:4432 -m 65536 -t udp=1m30s
This command-line increases the number of concurrent flows that softflowd will track to 65536 and
increases the timeout for UDP flows to 90 seconds.

softflowd -v 9 -i fxp0 -n 224.0.1.20:4432 -L 64
This command-line will export NetFlow v.9 flows to the multicast group 224.0.1.20. The export
datagrams will have their TTL set to 64, so multicast receivers can be many hops away.

softflowd -i fxp0 -p /var/run/sfd.pid.fxp0 -c /var/run/sfd.ctl.fxp0
This command-line specifies alternate locations for the control socket and pid file. Similar
command-lines are useful when running multiple instances of softflowd on a single machine.

FILES

       /var/run/softflowd.pid
               This file stores the process ID  when  softflowd  is  in  daemon  mode.   This  location  may  be
               overridden using the -p command-line option.

       /var/run/softflowd.ctl
               This  is  the  remote  control  socket.   softflowd  listens  on  this  socket  for commands from
               softflowctl(8).  This location may be overridden using the -c command-line option.

BUGS

       Currently softflowd does not handle maliciously fragmented packets  properly,  i.e.  packets  fragemented
       such  that  the  UDP or TCP header does not fit into the first fragment.  It will product correct traffic
       counts when presented with  maliciously  fragmented  packets,  but  will  not  record  TCP  or  UDP  port
       information.  Please report bugs in softflowd to https://github.com/irino/softflowd/issues

AUTHORS

       Damien Miller <djm@mindrot.org>
       Hitoshi Irino (current maintainer) <irino@sfc.wide.ad.jp>